How to Replace a Tub in Your Bathroom
How to Replace a Tub in Your Bathroom
Blog Article
How do you feel with regards to Tools You Need to Install a New Bathtub ?
Installing a tub isn't specifically brain surgery, but it does need strong plumbing, carpentry, and often, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably hard project. If the old tub is easily easily accessible, the task can relocate easily; if you need to open up a wall surface to remove the old bathtub and also place the brand-new bath tub, the task is much harder. In either situation, the job is within a house handyman's skills, although you will need a helper to move out the old tub and set in the new one. Make sure you have qualified yourself for the job and are comfortable attempting it. Rather than working with a contractor to take control of a halfway-completed job, it is much better to think about employing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This short article will help you mount a brand-new tub in your bathroom if you have already bought a new bathtub as well as don't need to change the setup of your previous water pipelines.
Your tools and material checklist should consist of the following:
Preparing for the Installment
First of all, the supporting frame provided with the bath should be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is essential to make sure that if the faucet includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps system to prevent pressure on the tub.
Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath ought to currently be ready to be suited its last position.
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, after that the first thing you should do is disconnect the water system. After doing so, activate the faucets to drain any type of water staying in the system. The procedure of removing the existing taps can be rather troublesome as a result of the limited access that is frequently the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a fabric prepared for the staying water that will certainly originate from the pipelines. Once the supply pipes have been eliminated, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning during this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Before moving on to fit the new taps, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, put the tub in the needed setting. The wooden boards are useful in evenly spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the bathtub until the spirit level reads level.
To mount faucets, fit all-time low of the outermost adaptable faucet port to the proper supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Switch on the water supply and check all joints and also brand-new pipework for leakages as well as tighten them if needed. Fill up the bathtub and also inspect the overflow outlet and the normal outlet for leakages.
Ultimately, take care of the bath paneling as explained in the producer's instruction manual. Tiling and also securing around the tub ought to wait until the bathtub has actually been utilized a minimum of once as this will certainly resolve it into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly require reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin making certain that the washing machines are in area between the faucet and also the sink. Protect the faucet in position with the producer given backnut. Once the faucet is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind should be linked to the faucet finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture a rigid seal, causing the water to permeate the wall surface in between the bath and the tiling, causing difficulties with wetness and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures as well as fittings. They are offered in tubes and also cartridges, and also can sealing gaps up to a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of drenched paper or soft rope. Remember to always fill the bathtub with water before sealing, to allow for the motion experienced when the tub is in use. The sealant can split relatively very early if you do not take into consideration this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise quickly offered on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our part on Tools You Need to Install a New Bathtub . Thanks a lot for taking a few minutes to read through our blog. Enjoyed reading our review? Please share it. Help another person discover it. We treasure reading our article about How to Install a Bathtub Yourself.
Schedule Now Report this page